Feet to meters
One foot is 0.3048 meter. Enter any value and the answer updates as you type.
Converter
Foot to Meter at a glance
21 rows| Foot | Meter |
|---|---|
| 1 ft | 0.3048 m |
| 2 ft | 0.6096 m |
| 3 ft | 0.9144 m |
| 4 ft | 1.2192 m |
| 5 ft | 1.524 m |
| 6 ft | 1.8288 m |
| 7 ft | 2.1336 m |
| 8 ft | 2.4384 m |
| 9 ft | 2.7432 m |
| 10 ft | 3.048 m |
| 15 ft | 4.572 m |
| 20 ft | 6.096 m |
| 25 ft | 7.62 m |
| 30 ft | 9.144 m |
| 40 ft | 12.192 m |
| 50 ft | 15.24 m |
| 75 ft | 22.86 m |
| 100 ft | 30.48 m |
| 250 ft | 76.2 m |
| 500 ft | 152.4 m |
| 1,000 ft | 304.8 m |
Quick pairs
tap to loadWhy people convert feet to meters
Building heights and aircraft cruising altitude are usually quoted in feet in the US and in meters almost everywhere else, so a skyscraper's height or a flight's altitude reported in one system often needs converting for an audience used to the other. A commercial jet cruising at 35,000 feet is close to 10,668 meters, a scale worth keeping as a mental anchor.
Recreational drone flying runs into the same pair: many countries set their hobbyist altitude ceiling in meters, while US guidance commonly cites a 400-foot limit (about 121.92 meters) for flying without special authorization. A pilot moving between countries, or simply reading rules written for a different one, needs to convert the stated ceiling before assuming their drone's altitude readout — which may display either unit — keeps them within it, especially since a flight controller set to the wrong unit can silently let a drone climb well past the legal limit.
Popular length conversions
6 pagesHow the foot to meter conversion works
A foot is defined as exactly 0.3048 meter, and the meter is the SI base unit of length, so converting in this direction is also an exact calculation.
Multiply a foot value by 0.3048 to get meters:
m = ft × 0.3048
One foot converts to 0.3048 meter. Six feet, about an average adult's height, converts to 1.8288 meters. And 100 feet, roughly the height of a ten-story building, converts to 30.48 meters.
Because 0.3048 is an exact, terminating decimal, converting feet to meters never produces a repeating fraction the way the reverse direction sometimes does for odd inputs. Two or three decimal places are enough for construction or hiking; four or more only matter for scientific or surveying work, where a fraction of a meter on a long run of feet can shift a total by a noticeable amount.
A frequent mistake is mixing up the standard foot with the US survey foot, a very slightly different unit (0.3048006096... meters) used in some older land records. For everyday purposes the difference is far too small to notice, but it's worth knowing the two numbers aren't quite identical if a figure comes from a legal survey document rather than a tape measure.
Questions
How many feet are in one meter?
One meter equals 3.280839895 feet.
Why does converting feet to meters sometimes give a long decimal?
Only some values work out cleanly — 1 foot converts to exactly 0.3048 meter because that's the defined relationship, but a measurement like 7 feet converts to 2.1336 meters, which can look less tidy depending on how many decimal places are shown.
Is there a fast way to estimate feet to meters in my head?
Divide by 3.3 for a close estimate, or multiply by 0.3 for an even faster rough figure; both run a little under the precise 0.3048 factor, so the true answer is always slightly larger.
What's a common error when converting feet to meters?
Dividing by 3.28 instead of multiplying by 0.3048 — both get to roughly the same place mathematically, but it's easy to pick the wrong operation under time pressure and end up with a noticeably off number.
Is a foot the same length everywhere it's used?
Almost — the international foot used here (0.3048 meter) is standard in everyday US and UK use, but a specialized US survey foot (about 0.3048006 meter) persists in some land-surveying records; the gap is far smaller than any measuring tape can detect.
More on precision and what leaves your device: see About and Privacy policy.